===============          ==================       =======================
README.TXT File          SAFE Version 8.1.1       Release Date 2007-10-19
===============          ==================       =======================


PLEASE READ THIS FILE!

It contains important information that is more current than what is in
the Manuals.

=========================================================================
SAFE V8.1.1 is a minor update to V8.1.0 and is only available on the ftp.
=========================================================================

CONTENTS
--------
  1. Installation Instructions for SAFE Version 8.1.0 
  2. Updating older version 8.xx from the ftp
  3. Significant changes from Version 7.00

1. Installation Instructions for SAFE Version 8.1.0
----------------------------------------------------

  The installation instructions are available in three places.  
     A.  The "SAFE Installation Card" link on the SAFE CD browser.
     B.  A printed document included with the program package.
     C.  In the SAFE_Install_Instructions.pdf file in the root directory 
         of the CD.
  The instructions include information about the software protection system used 
  and installation options and instructions. You can choose between a Standalone 
  or Network installation.

  For new Network installations, see the License Manager System Administrator's 
  Guide for more detailed information about the License Manager and the License 
  Manager Administration program "WlmAdmin.exe".

  This installation contains the License Manager program SentinelLM 7.2.0.23. 
  If you are currently running an earlier version of SentinelLM then it should 
  be uninstalled prior to installing this version. IMPORTANT!! Note that all 
  commuter licenses should be checked in before uninstalling the old version.
  

2. Updating older version 8.xx from the ftp
-------------------------------------------
  The update from the ftp is not a full installation. Only newer files are 
  included in the zipped file. These should be extracted in the folder where the 
  current program is.


3. Significant changes from Version 7.00
----------------------------------------
   We have listed only significant changes here. For a complete list of changes, 
   please see the separate file ReleaseNotes.PDF located in the SAFE 
   installation folder.  

  Changes from V8.1.0 to V8.1.1 (10/19/2007)
  -----------------------------------------
   - Incident 12660: The punching shear perimeter was being incorrectly 
     calculated from default column sizes for points supported on springs. 
     This has been resolved. The punching shear perimeter at load points and at 
     points supported by restraints or columns was correct and has not been 
     changed.
   - Incident 13037: Design check has been added for the ACI 318-05 design code.
   - Incident 13038: Design check has been added for the CAN/CSA A23.3-04 design 
     code.
   - Incident 13242: The design manual has been updated to include the two new 
     design codes.
   - Other minor Incidents, as detailed in ReleaseNotes.PDF.
 
  Changes from V8.0.9 to V8.1.0 (03/16/2007)
  -----------------------------------------
   - Solver recompiled to support 64 bit operating systems.
   - Support for other languages provided.
 
  Changes from V8.0.8/2 to V8.0.9 (10/10/2006)
  -----------------------------------------
   - Minor enhancements to Detailer.
   - Minor display bug fixes.
 
  Changes from V8.0.8/1 to V8.0.8/2 (09/19/2005)
  -----------------------------------------
   - Minor changes to allow large models with many
     load cases and combinations to be run.

  Changes from V8.0.8 to V8.0.8/1 (08/19/2005)
  -----------------------------------------
   - Minor change to calculation of punching perimeter
     for circular columns. Equivalent perimeter is used 
     instead of equivalent area.

  Changes from V8.0.7 to V8.0.8 (06/22/2005)
  -----------------------------------------
   - Indian code updated to IS456:2000.

  Changes from V8.0.6 to V8.0.7 (05/09/2005)
  -----------------------------------------
   - Indian code added.

  Changes from V8.0.5 to V8.0.6 (02/15/2005)
  -----------------------------------------
   - Reissued on CD.
   - A display bug that did not show wall reactions when
     slab releases were present has been corrected. This 
     was a display problem only. Results were correct.

  Changes from V8.0.4/1 to V8.0.5 (02/09/2005)
  -----------------------------------------
   - An error that caused the cracking deflections to be
     incorrectly computed when reinforcement was specified
     has been corrected. The deflection was overestimated.

  Changes from V8.0.3 to V8.0.4/1 (01/26/2005)
  -----------------------------------------
   - Error traps added to CSIDetailer.
   - Minor bug fixes.
 
  Changes from V8.0.2 to V8.0.3 (11/13/2004)
  -----------------------------------------
   - Several minor bug fixes and enhancements have been 
     made to the CSIDetailer. The CSIDetailer Help and 
     Manual has been updated to reflect the changes.

  Changes from V8.0.1 to V8.0.2 (10/18/2004)
  -----------------------------------------
   - A bug that caused the meshing of Poly areas 
     to be visibly incorrect in some rare cases
     has been corrected.
   - Minor enhancements and bug fixes to CSIDetailer.

  Changes from V8.0.0 to V8.0.1 (10/01/2004)
  -----------------------------------------
  - A bug that did not allow uplift analysis to be done if 
    detailer license was present has been corrected. It gave the
    error message "File *.y4s not found".
  - The newly introduced orthotropic flag in the slab property
    was not working properly. This has been fixed.

  Changes from V7.3.0 to V8.0.0 (09/15/2004)
  -----------------------------------------
  - A detailer program has been added to SAFE. This option
    requires a different license.
  - Waffles and Ribbed floors can now be analyzed and designed
    as equivalent slabs. The old program only allowed ribs to
    be modeled as beams.
  - The ACI design code has been updated to ACI 318-02.   

  Changes from V7.02 to V7.3.0 (10/06/2003)
  -----------------------------------------
  - A general poly area object has been added
  - New drafting constraints have been added
  - The tool bars have been updated
  - New Manuals have been added 
  - The Help has been updated

  Changes from V7.00 to V7.02 
  ---------------------------
  - Minor changes mostly relating to the graphics display

